Famous Distribution Box Manufacturers – SC(B) □ Series Epoxy Resin Dry Type Transformer – Changan Group
Famous Distribution Box Manufacturers – SC(B) □ Series Epoxy Resin Dry Type Transformer – Changan Group Detail:
Product introduction
SC(B) series epoxy resin dry-type transformer is flame-retardant, fire-proof, explosion-proof, maintenance free, pollution-free, small in size, because of the winding is encapsulated, and can be directly installed in the load center. At the same time, the scientific and reasonable design and casting process make the product have less partial discharge, lower noise and stronger heat dissipation capacity. Under the condition of forced air cooling, it can operate for a long time under 125% rated load. It is equipped with intelligent temperature controller, which has the functions of fault alarm, overtemperature alarm, overtemperature trip and black box. It is connected with the computer through RS485 serial interface and can be monitored centrally and control.
Because of the above characteristics, the product is widely used in power transmission system, such as hotels, restaurants, airports, high-rise buildings, commercial centers, residential areas and other important places, as well as subway, smelter, ship, offshore drilling and platform and other places with bad environment.
Model Meaning
Standards
GB/T 1094.1-2013 Power transformers – Part 1: General
GB/T 1094.11-2007 Power transformers – Part 11: Dry-type transformers
GB/T 10228-2015 Specification and technical requirements for dry-type power transformers
IEC60076-1:2011 Power transformers – Part 1: General
IEC60076-11:2018 Power transformers – Part 11: Dry-type transformers
Normal Environment conditions
1.Ambient Temperature: No more than +40℃
No less than -25℃
The monthly average temperature is no more than +30℃
The yearly average temperature is no more than +20℃
2.Altitude: No more than 1000m.
3.The power supply voltage’s wave is similar to sine wave.
4.Three-phase power supply voltage is approximately symmetrical.
5.The relative humidity of the surrounding air should be less than 93%. There should be no water droplets on the coil surface.
6.Installation Site: Indoor or outdoor.
Product features
1. The high voltage winding is made of enameled copper wire or film wrapped copper wire, and the low voltage winding is made of copper foil. The high voltage
winding is filled with glass fiber felt. In the vacuum state, the epoxy resin without filler is used for pouring, which forms a solid whole after curing, with high
mechanical strength, small partial discharge and high reliability.
2. Flame retardant, explosion-proof, no environmental pollution, environmental protection. It can be installed in the load center.
3. The core material is made of high quality cold-rolled oriented silicon steel sheet with full inclined seam laminated structure.
4. The coil does not absorb moisture, and the core and clamp are treated by special process, which can operate in high relative humidity and other harsh environment.
Intermittent operation without dehumidification treatment.
5. High resistance to short circuit, lightning impulse and overload.
6. Thin resin insulation layer inside and outside the coil, good heat dissipation performance.
7. Low loss, good power saving effect, economical operation and maintenance free.
8. Small volume, light weight, small floor space and convenient installation.
SCB11-30-2500/10kV Technical Parameter
| caRpaatecdity (kvA) |
Voltage combination High kvVo)ltage Taapnpging Low vol)tage |
cognrnoeucpted label | diNssoi-ploaatidon (w) | Load dissipation (W) | Ncuor-rIoeandt (%) | Imvpoeltdaagnece (%) | ExteIrniostraslilz4e-(ΦLx1W8 xH) (mm) | WTeoitgahlt (kg) | ||||
|
( |
r e |
(kV |
130℃ (B) |
155℃ (F) |
180℃ (H) |
|||||||
| 100℃ | 120℃ |
145℃ |
||||||||||
|
30 |
663 1.06 1101.5 |
±±25.5 | 0.4 | Dyn11 |
170 |
670 | 710 | 760 |
2.3 |
4.0 |
955×750×840 |
270 |
|
50 |
240 |
940 |
1000 |
1070 |
2.2 |
970×750×860 |
340 | |||||
|
80 |
330 |
1290 |
1380 |
1480 |
1.7 |
1015×750×925 |
460 | |||||
|
100 |
360 |
1480 |
1570 |
1690 |
1.7 |
1030×750×960 |
530 | |||||
|
125 |
420 |
1740 |
1850 |
1980 |
1.5 |
1060×750×1000 |
605 | |||||
|
160 |
480 |
2000 |
2130 |
2280 |
1.5 |
1090×900×1045 |
730 | |||||
|
200 |
±2±×52.5 |
550 |
2370 |
2530 |
2710 |
1.3 |
1105×900×1080 |
825 | ||||
|
250 |
640 |
2590 |
2760 |
2960 |
1.3 |
1180×900×1125 |
1010 | |||||
|
315 |
790 |
3270 |
3470 |
3730 |
1.1 |
1225×900×1140 |
1165 | |||||
|
400 |
880 |
3750 |
3990 |
4280 |
1.1 |
1330×900×1195 |
1490 | |||||
|
500 |
1040 |
4590 |
4880 |
5230 |
1.1 |
1345×900×1255 |
1650 | |||||
|
630 |
1200 |
5530 |
5880 |
6290 |
0.9 |
1540×1150×1175 |
1915 | |||||
|
630 |
1170 |
5610 |
5960 |
6400 |
0.9 |
6.0 |
1540×1150×1175 |
1915 | ||||
|
800 |
1360 |
6550 |
6960 |
7460 |
0.9 |
1600×1150×1220 |
2305 | |||||
|
1000 |
1590 |
7650 |
8130 |
8760 |
0.9 |
1645×1150×1285 |
2690 | |||||
|
1250 |
1880 |
9100 |
9690 |
10300 |
0.9 |
1705×1150×1345 |
3225 | |||||
|
1600 |
2200 |
11000 |
11700 |
12500 |
0.9 |
1765×1150×1405 |
3805 | |||||
|
2000 |
2740 |
13600 |
14400 |
15500 |
0.7 |
1840×1150×1475 |
4435 | |||||
|
2500 |
3240 |
16100 |
17100 |
18400 |
0.7 |
1900×1150×1560 |
5300 | |||||
|
1600 |
2200 |
12200 |
12900 |
13900 |
0.9 |
8.0 |
1765×1150×1405 |
3805 | ||||
|
2000 |
2740 |
15000 |
159000 |
17100 |
0.7 |
1840×1150×1475 |
4435 | |||||
|
2500 |
3240 |
17700 |
18800 |
20200 |
0.7 |
1900×1150×1560 |
5300 | |||||
Dimensions
SCB12-30-2500/10kV Technical Parameter
| caRpaatecdity (kvA) |
Voltage combination High kvVo)ltage Taapnpging Low vol)tage |
cognrnoeucpted label | diNssoi-ploaatidon (w) | Load dissipation (W) | Ncuor-rIoeandt (%) | Imvpoeltdaagnece (%) | ExteIrniostraslilz4e-(ΦLx1W8 xH) (mm) | WTeoitgahlt (kg) | ||||
|
( |
r e |
(kV |
130℃ (B) |
155℃ (F) |
180℃ (H) |
|||||||
| 100℃ | 120℃ |
145℃ |
||||||||||
|
30 |
663 1.06 1101.5 | ±±25.5 | 0.4 | Dyn11 |
150 |
670 | 710 | 760 |
2.3 |
4.0 |
955×750×840 |
270 |
|
50 |
215 |
940 |
1000 |
1070 |
2.2 |
970×750×860 |
340 | |||||
|
80 |
295 |
1290 |
1380 |
1480 |
1.7 |
1015×750×925 |
460 | |||||
|
100 |
320 |
1480 |
1570 |
1690 |
1.7 |
1030×750×960 |
530 | |||||
|
125 |
375 |
1740 |
1850 |
1980 |
1.5 |
1060×750×1000 |
605 | |||||
|
160 |
430 |
2000 |
2130 |
2280 |
1.5 |
1090×900×1045 |
730 | |||||
|
200 |
±2±×52.5 |
495 |
2370 |
2530 |
2710 |
1.3 |
1105×900×1080 |
825 | ||||
|
250 |
575 |
2590 |
2760 |
2960 |
1.3 |
1180×900×1125 |
1010 | |||||
|
315 |
705 |
3270 |
3470 |
3730 |
1.1 |
1225×900×1140 |
1165 | |||||
|
400 |
785 |
3750 |
3990 |
4280 |
1.1 |
1330×900×1195 |
1490 | |||||
|
500 |
930 |
4590 |
4880 |
5230 |
1.1 |
1345×900×1255 |
1650 | |||||
|
630 |
1070 |
5530 |
5880 |
6290 |
0.9 |
1540×1150×1175 |
1915 | |||||
|
630 |
1040 |
5610 |
5960 |
6400 |
0.9 |
6.0 |
1540×1150×1175 |
1915 | ||||
|
800 |
1210 |
6550 |
6960 |
7460 |
0.9 |
1600×1150×1220 |
2305 | |||||
|
1000 |
1410 |
7650 |
8130 |
8760 |
0.9 |
1645×1150×1285 |
2690 | |||||
|
1250 |
1670 |
9100 |
9690 |
10300 |
0.9 |
1705×1150×1345 |
3225 | |||||
|
1600 |
1960 |
11000 |
11700 |
12500 |
0.9 |
1765×1150×1405 |
3805 | |||||
|
2000 |
2440 |
13600 |
14400 |
15500 |
0.7 |
1840×1150×1475 |
4435 | |||||
|
2500 |
2880 |
16100 |
17100 |
18400 |
0.7 |
1900×1150×1560 |
5300 | |||||
|
1600 |
1960 |
12200 |
12900 |
13900 |
0.9 |
8.0 |
1765×1150×1405 |
3805 | ||||
|
2000 |
2440 |
15000 |
15900 |
17100 |
0.7 |
1840×1150×1475 |
4435 | |||||
|
2500 |
2880 |
17700 |
18800 |
20200 |
0.7 |
1900×1150×1560 |
5300 | |||||
SCB13-30-2500/10kV Technical Parameter
| caRpaatecdity (kvA) |
Voltage combination High kvVo)ltage Taapnpging Low vol)tage |
Cognrnoeucpted label | diNssoi-ploaatidon (w) | Load dissipation (W) | Ncuor-rIoeandt (%) | Imvp(e%da)nece oltag | ExteIrniostraslilz4e-(ΦLx1W8 xH) (mm) | WTeoitgahlt (kg) | ||||
|
( |
r e |
(kV |
130℃ (B) |
155℃ (F) |
180℃ (H) |
|||||||
| 100℃ | 120℃ |
145℃ |
||||||||||
|
30 |
663 1.06 1101.5 | ±±25.5 | 0.4 | Dyn11 |
135 |
605 | 640 | 685 |
2.3 |
4.0 |
955×750×840 |
270 |
|
50 |
195 |
845 | 900 | 965 |
2.2 |
970×750×860 |
340 | |||||
|
80 |
265 |
1160 |
1240 |
1330 |
1.7 |
1015×750×925 |
460 | |||||
|
100 |
290 |
1330 |
1410 |
1520 |
1.7 |
1060×750×960 |
560 | |||||
|
125 |
340 |
1560 |
1660 |
1780 |
1.5 |
1075×750×lO00 |
630 | |||||
|
160 |
385 |
1800 |
1910 |
2050 |
1.5 |
1105×900×1045 |
770 | |||||
|
200 |
±2±×52.5 |
445 |
2130 |
2270 |
2440 |
1.3 |
1120×900×1105 |
875 | ||||
|
250 |
515 |
2330 |
2480 |
2660 |
1.3 |
1195×900×1125 |
1055 | |||||
|
315 |
635 |
2940 |
3120 |
3350 |
1.1 |
1555×1150×1175 |
1190 | |||||
|
400 |
705 |
3370 |
3590 |
3850 |
1.1 |
1225×900×1140 |
1500 | |||||
|
500 |
835 |
4130 |
4390 |
4700 |
1.1 |
1315×900×1190 |
1700 | |||||
|
630 |
965 |
4970 |
5290 |
5660 |
0.9 |
1345×900×1265 |
1985 | |||||
|
630 |
935 |
5050 |
5360 |
5760 |
0.9 |
6.0 |
1555×1150×1175 |
1985 | ||||
|
800 |
1090 |
5890 |
6260 |
6710 |
0.9 |
1600×1150×1220 |
2360 | |||||
|
1000 |
1270 |
6880 |
7310 |
7880 |
0.9 |
1660×1150×1285 |
2775 | |||||
|
1250 |
1500 |
8190 |
8720 |
9330 |
0.9 |
1720×1150×1350 |
3310 | |||||
|
1600 |
1760 |
9940 |
10500 |
11300 |
0.9 |
1780×1150×1405 |
3940 | |||||
|
2000 |
2190 |
12200 |
13000 |
14000 |
0.7 |
1840×1150×1475 |
4595 | |||||
|
2500 |
2590 |
14500 |
15400 |
16600 |
0.7 |
1900×1150×1565 |
5495 | |||||
|
1600 |
1760 |
11o00 |
11600 |
12500 |
0.9 |
8.0 |
1780×1150×1405 |
3940 | ||||
|
2000 |
2190 |
13500 |
14300 |
15400 |
0.7 |
1840×1150×1475 |
4595 | |||||
|
2500 |
2590 |
15900 |
17000 |
18200 |
0.7 |
1900×1150×1565 |
5495 | |||||
Product detail pictures:
Related Product Guide:
We have the most advanced production equipment, experienced and qualified engineers and workers, recognized quality control systems and a friendly professional sales team pre/after-sales support for Famous Distribution Box Manufacturers – SC(B) □ Series Epoxy Resin Dry Type Transformer – Changan Group , The product will supply to all over the world, such as: Nigeria, Nepal, Maldives, Since the establishment of our company, we've realized the importance of providing good quality goods and the best before-sales and after-sales services. Most problems between global suppliers and clients are due to poor communication. Culturally, suppliers can be reluctant to question points they do not understand. We break down these barriers to ensure you get what you want to the level you expect, when you want it.
By Josephine from Albania - 2017.12.31 14:53
The supplier abide the theory of "quality the basic, trust the first and management the advanced" so that they can ensure a reliable product quality and stable customers.
By Victoria from Sri Lanka - 2018.09.12 17:18
